Brighten up your days with a DIY rainbow tassel earrings.

These pair of earrings use our popular cap tassels, all strung on hoop earrings! Flaunt this trendy and cheerful look.

Directions

1. Slide the following seed beads and tassels onto the hoop finding:
   Seed bead, purple, seed bead, blue, seed bead, green, seed bead, yellow, seed bead, orange, seed bead, red and seed bead.
2. Slide hoop end through the hole of the other hoop end.
3. Using your round nose pliers, roll a simple loop with the hoop end.
4. Open ear wire loop and slide on loop of tassel hoop. Close ear wire loop.
5. Repeat all steps for other earring.

Items used in earrings: SB00106, A013204, Z013686, Z013685, Z013684, Z013687, Z014017, Z013688, TCZ0078

Make a customizable and adjustable bracelet using your favorite beads, Griffin Silk Cord and Slide on Clasps.

Make sure to check out our FB video we did LIVE running through how easy it is making this bracelet. We made an adjustable bracelet with double strands of griffin cord strung with a side of metal beads and the other with seed beads and 4mm Gemstone beads.

What you’ll need:

• Griffin Silk Cord (Make sure to get Size No. 2 OR No. 4 and you’ll need a quantity of TWO)
• 4mm Gemstone Round Beads
• 11/0 Seed beads
• Metal Beads
• 4x5mm Slide on Clasp (Silver/Gold/Brass)

Directions

1. Unravel both your Silk Cord from its card and straighten them by running them through a wet towel a few times.
   
2. Flush both cord ends together and make an overhand knot with both ends.
3. Using both needles, slide on a gemstone bead.
4. Make another overhand knot with both cords about 4″ from the first knot you’ve made.
5. Using both needles, slide on the Slide on Clasp and pull it down next to the knot you’ve made.
6. With one silk cord, slide on a sequence of seed bead and metal bead until the length of these beads are long enough to wrap around your wrist. Make sure to end with a seed bead. Set this cord and needle aside.
7. With the other silk cord, slide on a sequence of seed bead and 4mm gemstone until the length of these beads are the same as the ones in step 6. Make sure to send with a seed bead..
8. Take both cords and make an overhand knot close enough to your seed bead.
9. Sew both needle through the Slide on Clasp, going the same way as you did in Step 4. This will criss cross the ends.
10. Using both needles, slide on a gemstone bead.
11. Slide the bracelet around your wrist to the widest part, which is around the middle part of your hand. This will lengthen your cord ends and determine where you will knot your ending knot. Make your knot and cut off excess cord.
12. The other end will be longer, so you will need to make another knot to sit closer to the Slide on Clasp.
13. Done! Slide your bracelet on and with your middle finger, hold one gemstone end while you pull the other gemstone end with your other hand to cinch the bracelet around your wrist.
    

Facebook Video

Bracelet Samples

We are LOVING this blue and silver combo! Heidi would agree also.

Items used in bracelet: SDL4RD-8, A006569 (2), SB00422, Z008576, A021442 (2)

In this bracelet, we did a full row of brass beads instead of a seed bead and metal sequence. Go ahead and make it your own!

Items used in Apple Jasper Bracelet: A022196, A006569, SB00423, APL4RD-8, Z008577

Make easy DIY jewelry using Beadable Components and adding POPS of color with Miyuki Delica Seed Beads. Here are ways to bead and use the beadable components.

From our recent Trends We Love, our new Beadable Components are what you need for an easy bead-stitch project. These pairs well with our 11/0 Miyuki Delica Seed Beads or beads with a width of 1.5mm or thinner. Our projects uses the basic ladder stitch. Here is a look at how a ladder stitch is done to sew through the channels. Make sure when you’ve sewn through your pattern or channels, to sew through them again to strengthen the pattern.

Here are some projects using these beadable components:

Beadable Ring Pendant

The Beadable Ring Pendant (Silver or Gold) has 24 channels and fun options to designing with this piece. Each channel holds 3 Delica beads. Here are a few ideas.

On the left is a pretty pair of pink and gold earrings. We even added a pearl dangle at the bottom! Make sure to use size 24-gauge headpins if adding dangles to beadable components.

Items used in earrings: Z011337 (2), A019635, SW00665 (2), TC02298, SB00269, SB02332 (A015211 & A006587)

In the middle, we’ve made a rainbow wheel with the beadable pendant. Attach it to your necklace chain for this easy DIY necklace!

Items used in rainbow pendant necklace: Z011336 (2), SB03546, SB02343, SB02336, SB02310, SB02311, SB03545, SB02327, SB02349, A001528, Z001033 (A015211 & A006587)

And lastly we created an ombré effect with the pendant on the right.

Items used in right pendant: Z011336 (2), SB01824, SB01822, SB01826 (A015211 & A006587)

Beadable Teardrop Pendant

Love the shape of the classic teardrop! This beadable component is much easier to sew through since it only has 5 channels to work with. Each channel holds different amounts of Delica beads. The outer channel holds 13 Delicas, the inner two holds 15 Delicas and the middle holds 16. Here are two ways to using this beadable component.

The necklace on the right uses the amount of correct amount of Delicas for each channel. We’ve also used two colors to add a design to its channels. Then, using 24-gauge jump rings, we’ve added small tassels to the bottom holes of the pendant before making a fun necklace with it!

Items used in necklace: Z011339, SB00269, SB02336, A002413, Z013681, Z001033 (A015211 & A006587)

And who wouldn’t love a pair of earrings! On the right, we have a charming pair of gold earrings using Delica beads and metal tube beads. The tube beads has the small thickness as Delica seed beads and works perfectly for these beadable components.

Items used in earrings: Z011342 (2), Z009196, SB003545, A014108 (A015211 & A006587)

Check out this lovely tutorial courtesy of Leather Cord USA. Learn to make celtic knots with leather cord and use the skill to make fun jewelry designs!

Our friend, Michelle from Leather Cord USA provided us with this great tutorial on how to tie the double celtic knot using two pieces of leather cord! Make yours today.

What You’ll Need:

• 2 – 1.5mm LeatherCord USA Leather (2 Meter Length)
• 2 – End Cap (Suggestion item# A010436)
• Large-Hole Gemstones
• 10″ or More of Chain link
• Clasp & Jump Ring
• Needle Nose Pliers & Cutter

Step by step instructions:

1. Take the two strands of Round Leather Cords and place evenly side by side then fold in half, creating four strands grouped in two.
2. Lay leather flat on a table or board
3. Take the right side group of two strands and create a loop laying it on top of the left strands. This will create three openings: top, middle and left (outside) as indicated in the photo below.
4. Take the left side and cross the cord over the tail of the right side then under the base of the top opening and feed through then back down the middle opening and up through the left opening.
5. Gently pull both tails while adjusting the knot into place. (Be sure to keep the strands lying flat while pulling.)
6. Repeat steps 3-5 for the left side: Take the left tail and create a loop laying it on top of the right strands. Take the right side and feed the cord over the left tail then under the base of the top opening and feed through then back down the middle opening and up through the left opening.
7. Repeat all steps to create five individual knots.
8. Feed one Large Hole Bead on the two center strands
9. Feed one Large Hole Bead on the two left strands and one on the two right strands
10. Feed a final Large Hole Bead on the two center strands
11. Repeat the knot pattern from above for another five knots.
12. Cut the top loop (starting point) in half
13. Add a drop of adhesive to the inside of the end cap and place all four strands in, give a slight twist and hold everything in place for a few seconds.
14. Repeat step 13 for the opposite side
15. Take the chain provided and judge the exact length you want the final piece to be. Cut chain in half.
16. Attach each side of the chain to the leather piece by attaching chain to end cap with jump ring. Repeat process to other end cap and chain.
17. Attach the lobster claw to one end of your chain with a jump ring. Add a jump ring to other chain end.
18. Voila!!!! You are done! Now go show off your work of art for the world to see!

Visual look at how you will continue your necklace braids:

Other Examples

Simplify this knot by making one knot and adding a gemstone pendant to it’s center loop!

You can even make a smaller version for earrings!

This DIY statement necklace will become your glamorous accessory of the season. Designed with our Bib connectors and Chinese crystals, all you need to know in order to make this necklace is the basics of making a simple loop and opening a jump ring!

What you’ll need to make this necklace:

• Diamond Design Curved Bib Pendant Connector (Z021568)
• 3 Inch Headpins (A019679)
• 11mm Teardrop Chinese Crystal (Used in necklace: A016579)
• 4mm Antiqued Silver-Plated Corrugated Round Bead (Z001371)
• 2 feet of Antique Silver Chain (Used in necklace: CH00025)
• 5.5mm Antique Silver Jump Rings (X003062)
• Clasp (Used in necklace: Y012952)

Directions

1. On a headpin, slide on a round bead and teardrop bead. Make a simple loop. Open loop and slide dangle to first hole of bib connector.
2. On a headpin, slide on a round bead, teardrop bead and round bead. Make a simple loop. Open loop and slide dangle to next hole of bib connector.
3. On a headpin, slide on a round bead, teardrop bead, round bead and teardrop. Make a simple loop. Open loop and slide dangle to next hole of bib connector.
4. On a headpin, slide on a round bead, teardrop bead, round bead, teardrop and two round bead. Make a simple loop. Open loop and slide dangle to next hole of bib connector.
5. On a headpin, slide on a round bead, teardrop bead, round bead, teardrop, round bead and teardrop. Make a simple loop. Open loop and slide dangle to next hole of bib connector.
6. On a headpin, slide on a round bead, teardrop bead, round bead, teardrop, round bead, teardrop and two round bead. Make a simple loop. Open loop and slide dangle to next hole of bib connector.
7. On a headpin, slide on a round bead, teardrop bead, round bead, teardrop, round bead, teardrop, round bead and teardrop. Make a simple loop. Open loop and slide dangle to next hole of bib connector.
8. On a headpin, slide on a round bead, teardrop bead, round bead, teardrop, round bead, teardrop, round bead, teardrop and round bead. Make a simple loop. Open loop and slide dangle to next hole of bib connector.
9. Repeat step 7 for next hole on bib connector.
10. Repeat step 6 for next hole on bib connector.
11. Repeat step 5 for next hole on bib connector.
12. Repeat step 4 for next hole on bib connector.
13. Repeat step 3 for next hole on bib connector.
14. Repeat step 2 for next hole on bib connector.
15. Repeat step 1 for next hole on bib connector.
16. Cut two pieces of chain at 6″ to 8″ long.
17. Open jump ring and slide on one end of chain and one end of bib connector. Close jump ring.
18. Open another jump ring and slide on other chain and to other end of bib connector. Close jump ring.
19. Open another jump ring and slide on one end of the chain and through ring of clasp.
20. Repeat steps 9 with another jump ring and other clasp ring.

Our GoodyBeads Designers came together to challenge their skills in designing with one product. Today’s product is the Long Drop Chandelier Earrings/Pendants (Z013693). Check out our three different pairs of earrings our designers came up with.

Get this featured component today and have fun creating!

Heidi Tassel Chandelier Earrings

Heidi’s design is true to her love of tassels and TierraCast components. Her gorgeous design turned out very “HEIDI” like!

Items used in earrings: Z013693, Z014010, TC00201 (6),  TCZ0077, TC01259 (12)

Tory Acetate Post Earrings

Tory created some Statement Earrings with a beautiful acetate component and Swarovski® round crystals. Plus, playing off on a popular jewelry trend, she finished off her design with Post Earrings.

Items used in earrings: Z012450, Z013693, A008182, Z011550, A001529, Z007586,  Z008989, Z019697, SW00100 (2)

So Moon & Star Earrings

So went rogue and designed a cute pair of earrings with a celestial theme. She created a staggering effect and added a charm to each loop on the chandelier component.

Items used in earrings: Z013693, CH01194, A002413, TC02297, Z020488 (2), TC00055 (2), Z011883 (2)

Learn how easy it is to macrame 3mm deerskin lace on a Woven Straw Ring for a cool and hip pair of earrings!

Macrame is making waves along side the fiber trend. Our Designer, Tory did a tutorial on how to make a single half hitch knot with 3mm deerskin lace around a woven straw ring. It revises our favorite woven straw component into fall fashion and even back to school wear!

What you’ll need:

• Handmade Woven Straw Ring – Z001659
• 3mm LeatherCord USA Deerskin Lace
  OR
• 3mm or 5mm LeatherCord USA Deertan Lace
• Super New Glue
• Earring Finding and 5-6mm jump ring
• Optional tool: Bead Reamer

Tutorial

1. Cut two pieces of 1 meter of lace each.
2. Fold lace in half and make a lark’s head knot on the straw ring. (Make sure to keep the smooth side sitting outwards.)
3. With each strand of lace, make a single half hitch knot working outward around the ring to both sides of the lark’s head knot you made in step 2.
4. Make 6-8 half hitch knots on both sides of the lark’s knot on the straw ring.
5. Take the lace end and tuck it behind your third loop on the backside of your knotted straw ring. Do the same to other end.
6. Add a small dab of glue to keep ends in place.
7. Cut excess lace.
8. Complete your earrings with making a hole in your woven opposite of lace/leather knots, with a bead reamer or awl. Add your earring finding to woven straw with a jump ring and through the hole you made.
9. Repeat all steps for other earrings.

Video Tutorial

Tutorial starts at 4:20 minutes.

Examples

Items used in examples using Deertan lace: Z001659, Z015550, Z015610

In this example, Deertan lace was used. The one the left is 3mm and the left is 5mm.

Items used in earrings: Z001659, A010962, Z008989, A001529

Leather necklaces with a gemstone pendant are easy to make once you get the basic sliding/slip leather knot down. Check out our easy tutorial to tying a gemstone necklace of your own.

The functionality of the sliding knot is mainly what it states, it slides. When you make a sliding knot, you are making a knot over the other leather piece so that the other piece slides back and forth, which can make a necklace or bracelet adjustable. You can check out our previous blog post on making a sliding knot.

If you’ve watched the video, you will see that we’ve altered the first portion of the necklace video by creating a two, coiled sliding knot to pinch the leather together at the top of the pendant. This will create somewhat of a bail so that pendant swingings nicely back and forth.

What you’ll need for tutorial:

• 1.5mm leather cord
• Dakota Stones Gemstone Pendants (with a side, top-drilled hole)

Tutorial

Sliding/Slip Knot Tutorial

Check out video/blog post on how to make a sliding knot in Step 8. Knot tutorial begins at 0:40.

Necklace with Gemstones

Items used in necklaces: Z019148,  PEN-YJD28X32DP-FF, MRQ16-60NUG, PEN-PDC35-64FF

Our selection of beadable accessories are one of our favorite categories to play with. We’re giving you a basic pattern at how to bead stitch a beadable cuff link with Miyuki Delica beads.

What you’ll need for beadable link:

• Beadable Cuff Link (Silver/Gold)
• Fireline Beading Thread
• Miyuki Size 11/0 Delica Beads
• Needle
• Optional: Thread Zap

Tutorial

As you can see from the illustration, you will see how to ladder stitch across the channel of the beadable cuff link, while adding 3 Delica seed beads inside the channel. Add different colors and create fun patterns to complete your Cuff Link.

Make sure to Click and Download the PDF Tutorial Pattern. You will also have a blank template for you to design and color a custom pattern for yourself. Here are some sample patterns you can see in the downloadable pdf also:

Items used in samples:

• First Sample – Z001457, SB00223, SB02322, SB02336
• Second Sample – Z001458, SB02336, SB00269, SB03545
• Third Sample – Z001457, SB00223, SB02336, SB00269

Pearl jewelry is back in a big way. These DIY jewelry projects aren’t your mother’s jewelry, but a modern twist on a classic trend!

Pearl jewelry is back this year with flare! You don’t need to be ruffled with a string of pearls, weighing or dating you. Create minimal jewelry with a small hint of pearls is the new classy and modern way! Here are four pair of earrings you can learn to love and make all in minutes using Swarovski Pearls!

Golden Pearls Post Earrings

Items used in earrings: A019681, Z001831, SW00666 (2)

A lot of trending jewelry has pearls being paired with gold findings. Here is our simple DIY on this style! To make, slide a pearl on your headpin and make a simple loop. Open loop and slide on post earring hole. Repeat for other earring!

Tiered Drop Pearl Earrings

Items used in earrings: SW00671 (2), SW00672, (2), SW00673 (2), A019629, A019682, Z003694

A cascade of pearl earrings are light and has so much movement!

Directions:

1. On a headpin, slide on a 6mm pearl and make a simple loop.
2. Open an eyepin loop, slide on dangle in Step 1 and close loop. Slide on a 6mm pearl and make a simple loop.
3. Open another eyepin loop, slide on loop you made in Step 2 and close loop. Slide on a 8mm pearl and make a simple loop.
4. Open loop you made in Step 3, slide on loop of earring finding and close loop.
5. Repeat all steps for other earring.

Pink Pearl Drop Earrings

Items used in earrings: SW01605 (2), Z010803 (2), A019656, TC02297

Another classic way to make earrings is making a pair of drop earrings with a cone cap.

Directions:

1. Slide on a headpin, 10mm pearl and cone cap.
2. Make a wrapped loop.
3. Open earring finding loop and slide on your pearl dangle.
4. Repeat all steps for other earring.

Pearl Dangle Hoop Earrings

Items used in earrings: SW01606 (2), A019697, Z011592

There’s tons of variation on the classic hoop earrings. With it, we’ve added a pearl dangle to the hoop to give it extra LOVE, we used a large 12mm pearl for added drama.

Directions:

1. On a headpin, slide on a 12mm pearl and make a simple loop. (Make a simple loop small enough to slide over the thickness of the earring finding, but not too big that it will slide off the ball end of the earring.)
2. Open pearl dangle loop and slide on earring finding. Close loop.
3. Repeat all steps for other earring.

We have three lovely projects using August’s Swarovski Psychology of Color: Rose Water Opal.

Beaded Fan Necklace with Swarovski Crystals

Items used in necklace: (12) SWZ0469, SB00107, SB00423, A021148, A006585, A015211, A011519, (2) CH01096

Get FREE Downloadable PDF Pattern Tutorial Here!

Gold & Silver Rose Opal Earrings

Items used in earrings: (4) SWZ0469, SB00423, A011519, Y018889, Z010751, A007659, A011528, Z012031

We mixed up the fun in this pair of earrings with gold and silver findings. It adds stunning layers and surely makes the crystals stand out!

Directions:

1. On a headpin, slide on a gold seed bead, bicone and another seed bead.
2. On an eyepin, slide on a gold seed bead, bicone and another seed bead.
3. Open loop from Step One and slide on brushed ring link. Close loop.
4. Open gold jump ring, slide on brushed ring link and one hole of gold brushed disc. Close jump ring.
5. Open a loop of link from Step Two, slide on other hole of gold brushed disc and close loop.
6. Open earwire loop and slide on other end of crystal link and close earwire loop.
7. Repeat all steps for other earring.

Rose Water Rhapsody

Our friends at Swarovski Create your Style, designed this stunning necklace with Rose Water Opal crystals and Fine Rocks Tube beads.

What you’ll need:

• (24) 3mm Rose Water Opal Bacon Crystal
• (88) SWZ0469
• (44) SWZ0470
• (42) SW01900
• (6) SW01902
• (2) SW02020
• (1) SW01733
• (3) 14x10mm Rose Water Opal Fancy Stone
• (3) 14x10mm Rhodium Plated Fancy Stone Setting
• (1) TC01871
• (6) TC00278
• (3) TC01253
• (2) TC00853
• (2) TC01899
• (1) FTBW0001
• SW01830
• Alcohol Wipes

Directions:

1. Using alcohol to wipe clean all the findings and set to dry.
2. Using one fancy stone, blue in matching setting and set aside for 24 hours to dry. Repeat two times and set aside.
3. Using one eyepin, attach one pendant made in Step 2, then slide on a bead cap, on SW02020 and another bead cap. Make a simple loop. Repeat one more time and set aside. Repeat one more time and set aside.
4. Using another eypin, attach one pendant made in Step 2, then slide on a bead cap, on SW01733 and another bead cap. Make a simple loop.
5. Cut beading wire into two 20″ pieces.
6. Using both wires together, slide on a SW01902, component made in Step 3, SW01902, SWZ0469, SWZ0470, SWZ0469, SW01902, one component made in Step 4, SW01902, SWZ0469, SWZ0470, SWZ0469, SW01902, component made in Step 3, and SW01902. Position all these in the center of the two strands of wire.
7. Take all remaining 4mm bicone beads and pour them onto your bead mat. Mix them all together.
8. Starting with the right side of the necklace and only using one of the two wires coming out of the 6mm bicone bead, string on three 3mm bicone beads. Now using your bead mix you created in Step 7 randomly string on 42 4mm bicone beads. String on three 3mm bicone beads. Repeat for this step for the second empty wire.
9. Using both wires, slide on one crimp bead and one end of the toggle. Crimp to close and add crimp cover.
10. Repeat Steps 8-9 to make left side of the necklace.

For August, Swarovski’s Psychology of Colors pick is Rose Water Opal. Check out how feminine and sophisticated this hue is!

Indulge yourself with this color! Rose Water Opal is light and sweet like a glass of Pink Lemonade! Here are some Swarovski colors to match this lovely hue:

• Rose Water Opal & Rose Water Opal AB
• Vintage Rose
• Rose & Light Rose
• Rosaline
• Blush Rose

Rose Opal Jewelry

Swing over to our other blog post with designs with Swarovski Rose Water Opal crystals.

We have some NEW exclusive enamel components that we could not help but make some gorgeous DIY jewelry with! Here are 5 different DIY jewelry to inspire you!

Enamel Earrings

Items used in earrings: Z001831, (2) Z016108, Z004939, A011517

Directions:

1. Open loop of tassel, slide on a loop on enamel link and close loop.
2. Open jump ring, slide on other loop on enamel link and through hole of post earrings. Close jump ring.
3. Repeat all steps for other earring.

Items used in earrings: (2) Z015957, Z016027, A011517

Directions: Open small jump ring and slide on enamel dangle and loop of post earrings. Close jump ring and repeat.

Enamel Bracelet

Items used in bracelet: Z016188, Z012152

Directions: Open jump rings on adjustable bracelet, slide on a loop from enamel link. Close jump ring. Repeat for other link loop.

Enamel Necklace

Items used in Necklace #1: A002735, (2)A008135, Z016017, A011517, A008808

Directions: 

1. Cut large Oval Chain with 4 Links.
2. Cut 2 inches off of the 2 feet of A008135, rollo chain.
3. Open large jump ring and attach oval chain to the 2″ rollo chain. Close jump ring.
4. Open another large jump ring and attach other end of oval chain and the remainder of the rollo chain. Close jump ring.
5. Open small jump ring, slide on one end of chained piece and through enamel pendant loop. Close jump ring.
6. Repeat step 5 with another small jump ring and other chain end.

Items used in Necklace #2: Z016327, Z007681, (2) CH00976, Z011514, Z011397

Directions:

1. Open large jump ring and slide through one hole of connector pendant and tassel loop. Close jump ring.
2. Open another large jump ring and slide through other hole of connector pendant. Close jump ring.
3. Open oval jump ring and slide on one end of your chain and through jump ring from Step 2. Close jump ring.
4. Repeat Step 3 to other chain end another another oval jump ring.

We have a very simple pattern for you today using the Cymbal Remata Bead Ending and 8/0 seed beads. Check out this free pattern today, designed by So Vang.

What you’ll need:

• Cymbal Remata Bead Ending (Silver/Gold)
• 8/0 Silver or Gold Seed Bead
• Second color of 8/0 Round Seed Bead
• Earwire Findings
• Needle and Fireline Beading Thread
  AND
• Geometric Drop Earrings with Cymbal Remata PDF Pattern Tutorial

Geometric Drop Earrings with Cymbal Remata

Items used in Earrings: Z004568, SB00076, SB00107, TCZ0139, A006585, A015211

Because we love tassels, throw a tassel on it!

Items used in Earrings: Z004564, SB00114, SB00106, TCZ0077, A006585, A015211, A002413, Z013685